TECHNICAL DATA
35.40mm Plastic Cutting Board
$10.00
RELATED PRODUCT
RELATED PRODUCT
RELATED PRODUCT
You may find a list of products that you can use with this product, down below.
Belt Punch Hardened Cutting Edge – Milled Clearing Hole
$10.00 – $58.00Micron hand tools are made of high quality stainless steel material. Remember to use a plastic mallet, not a steel hammer.
This set can make the following hole sizes; 1(3/32″), 2(7/64″), 3(1/8″), 4(5/32″), 5(11/64″), & 6(3/16″)
No. 147 – Drive Punch
$25.00 – $25.50• These punches should be used on an Micron Cutting Board.
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 149 – Arch Punch – size from 13mm to 24mm
$30.00Osborne arch punches are forged in one piece from the finest special carbon steel in sizes from 1/8” to 2-1/8” diameter.
Larger sizes are made with our properly engineered two piece welded construction. A unique feature of the Osborne arch punch is the inside taper which permits the punchings to clear easily through the barrel. Punches have fully polished barrel. The cutting edge is fully hardened all the way through and properly finished to provide long use trouble free punching. Original and correct design for cutting. Meet government standards.
These punches should be used on an Micron Cutting Board..
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 149 – Arch Punch – size from 25mm to 36mm
$30.00Osborne arch punches are forged in one piece from the finest special carbon steel in sizes from 1/8” to 2-1/8” diameter.
Larger sizes are made with our properly engineered two piece welded construction. A unique feature of the Osborne arch punch is the inside taper which permits the punchings to clear easily through the barrel. Punches have fully polished barrel. The cutting edge is fully hardened all the way through and properly finished to provide long use trouble free punching. Original and correct design for cutting. Meet government standards.
These punches should be used on an Micron Cutting Board..
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 149 – Arch Punch – size from 37mm to 48mm
$30.00Osborne arch punches are forged in one piece from the finest special carbon steel in sizes from 1/8” to 2-1/8” diameter.
Larger sizes are made with our properly engineered two piece welded construction. A unique feature of the Osborne arch punch is the inside taper which permits the punchings to clear easily through the barrel. Punches have fully polished barrel. The cutting edge is fully hardened all the way through and properly finished to provide long use trouble free punching. Original and correct design for cutting. Meet government standards.
These punches should be used on an Micron Cutting Board..
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 149 – Arch Punch – size from 49mm to 55mm
$30.00Osborne arch punches are forged in one piece from the finest special carbon steel in sizes from 1/8” to 2-1/8” diameter.
Larger sizes are made with our properly engineered two piece welded construction. A unique feature of the Osborne arch punch is the inside taper which permits the punchings to clear easily through the barrel. Punches have fully polished barrel. The cutting edge is fully hardened all the way through and properly finished to provide long use trouble free punching. Original and correct design for cutting. Meet government standards.
These punches should be used on an Micron Cutting Board..
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 223 – Revolving Punch
$93.70The frame is made of highly polished steel and the cutting dies are simply pushed in for easy replacement. Replacement cutting tubes are also available.
This set can make the following hole sizes;
0 (5/64”), 1 (3/32”), 2 (7/64”), 3 (1/8”), 4 (5/32”) & 6 (3/16”)
No. 245MM – Metric Belt Punch
$6.50Round shank. Hardened cutting edge – milled clearing hole. Variety of sizes.
• These punches should be used on an Micron White plastic cutting board.
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
No. 357 – Pin Punch
$6.00Forged from the finest quality high carbon steel. Hardened and tempered points for industrial use. Pointed ends are highly polished. Hexagon shanks with industrial finish. Variety of sizes.
No. K-245 – Belt Punch Set
$49.58Kit contains the most frequently used sizes packed in a sturdy vinyl pouch.
These punches should be used on an Micron Cutting Board..
The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.
Reviews
There are no reviews yet.